PC freezes during guided installation

Installing Zorin OS
#5

Please make sure that you are using Zorin OS 15.2 Lite or one of the Lite derivatives (Ultimate Lite or Education Lite), as these are the only editions of Zorin OS that run on computers with less than 2 GB of RAM.

After booting the Zorin OS Installation USB drive to the desktop, please follow these steps without opening any other apps:

  1. Click on the network indicator in the left side of the bottom panel to connect to your network
  2. Open the Zorin menu > System > Terminal
  3. Enter the following command: sudo apt update
  4. After the command finished running, close the Terminal window
  5. Double-click the “Install Zorin OS 15.2” icon on the desktop to start the installation process normally

Please note that running Zorin OS from a USB drive will run slower and uses more system resources & RAM than after it’s installed to the computer.

1 Like
#6

Hi,
I tried running the sudo apt update and when it finished I closed the terminal but still, during the guided installation it freezes. I’ll send a pic of gparted, I hope this can help.

image
image1280×960 233 KB

1 Like
#7

It does help; that answered the partitions question perfectly.
Given that it froze on “additional drivers” and during installation, I wonder if the graphics drivers are responsible.
Something you may try:
Boot up the machine from the USB and when you reach the Grub Screen that says

  • Try Zorin
  • Install Zorin
    and so on… Note: this is the grub screen you see prior to trying out the OS in the LiveCD demo…
    Do not select any of those options but instead hit the “e” key.

This will open a Terminal Text Editor for a temporary grub. Using your arrow keys, navigate through to where it says “quiet splash.”
Replace just the words “quiet splash” with “quiet splash nomodeset”
Then hit ctrl+x keys to continue onward. Try the installation again.
If it freezes, you can try repeating the above steps but instead of adding “nomodeset”, instead add “quiet splash modprobe.blacklist=nouveau”
And try to install again.

Assuming either of the above gets things moving again, be sure to select the option during installation to install third party drivers.
Once installed, boot up and then immediately repeat Azorins advice above:
Open a terminal and enter in

sudo apt update

then

sudo apt upgrade

1 Like
#8

Thank you for the detailed answer, but I pressed it and what happen is the countdown to the automatic boot restarts

1 Like
#9

Can you try using the arrow key to Highlight “Try Zorin” and then hit the “e” key?

1 Like
#10

image
image1280×489 221 KB

I highlighted “Try or Install Zorin OS”, pressed the “E” key but the screen stays still
Sorry for the bad quality pic

1 Like
#11

Well, then.
Um…
Have you tried dropping down once to Try or Install Zorin OS (safe graphics)?
That does what we are trying to do… and I may be outdated here. :smiley:

1 Like
#12

Based on your screenshot, it looks like you’re seeing the legacy USB boot menu (which appears if your computer doesn’t support UEFI).

Instead of pressing the “e” key here, please press the Tab key to edit the boot parameters as in Aravisian’s post.

2 Likes
#13

This… is good to know. Learned somethin’ new.

Aravisian: Solving problems one step to maybe fifty steps at a time.

3 Likes
#14

No problem :wink:
So, I tried with the tab key, as @AZorin suggested. I modified the text but when I pressed Enter, some text appeared (something like “no caching”), but it always happens but this time it was way more bigger and pixelated and after that a glitchy screen appeared. This happened when I selected the “Safe graphic” option and when I modified the text. It looks like the graphics is not causing the problem, I think, but I don’t know anything about Linux, and you are way more specialized!

I don’t know if it can help, but on the PC I have Lubuntu, recently I typed something wrong in the terminal and after that all system applications couldn’t work with internet, for example I can’t use:

use sudo apt-get update/upgrade
check application updates

Maybe this is causing this issue? Should I try installing another distro and then Zorin?

1 Like
#15

It sounds like graphics issues to me. I wonder if, as Azorin pointed out, the mode of Legacy being used is involved. Can you go into the MB BIOS and just check that it is set to legacy and what it offers?
I do not think that the Lubuntu setting can affect this installation in any way. This LiveCD and installation is running independently of that.

This is true for installing another distro and then trying the Zorin installation again. And, you may run into the same trouble installing the other distro.

1 Like
#16

Hi guys, I have a small update!
Guess what? I flashed on the same USB Xubuntu 18.04.5 and I could bypass the updates and drivers step! Now I’m busy, but when I’ll be free I’ll install Xubuntu and then Zorin! And let’s hope everything will be ok

So, I didn’t check the BIOS, but this PC only supports Legacy boot (it’s from 2007)

1 Like
#17

Hi guys,
I successfully installed Xubuntu. I downloaded again the Zorin ISO and flashed it on the same USB.
It’s stuck (after 1 hour) at the “Updates and other software” page, the only that’s working is the mouse cursor but it’s very laggy

image
image1280×960 332 KB

What should I do?

1 Like
#18

Can you check through the suggestions in this AskUbuntu thread and see if any help?

1 Like
#19

Hi,
Thanks for sending me this link! Unfortunately, the problem persisted.
For no reason, I downloaded Zorin 12.4 and it worked!

Thanks for the help! So happy to use Zorin! :smile:

1 Like
#20

So Zorin 15 was still “too new” for the hardware?
Good thing Zorin 12.4 still is supported with updates for a while yet. :wink:

1 Like
#21

I flashed v.15 and I could install it! The only that’s not working is Wi-Fi, which had no problems in 12.

1 Like
#22

Could you please start a new thread on that and describe in detail what it is doing? What you have tried, so far. What you see when you check your config in terminal…

1 Like
#23

Just turned off and on the Wi-Fi driver and now it’s working!

2 Likes
#24

5 posts were split to a new topic: Zorin 12 installation